Download FDNYC G60 Practice Exam: Fire Safety Questions and Answers and more Exams Safety and Fire Engineering in PDF only on Docsity!
FDNYC G60 Practice Exam Questions And Answers
(Verified Answers)
1. The pre-hot work check must be conducted by the responsible person...-
ANS Once per day
2. Piped gas lines should be... ANS Shut off if there is a fire
3. Don't aim the fire extinguisher at... ANS center of the flame
4. When it is not possible to shut off a gas supply and the gas supply is limited, you should....
ANS allow the fire to burn itself out and call 911
5. Trained Certificate of Fitness holders should only attempt to extinguish fires that are.... ANS
limited in size and can be readily extinguished
6. Class A fire are caused by... ANS ordinary combustible materials
7. Class B fire are caused by... ANS flammable or combustible liquids
8. Class C fires are caused by... ANS electrical equipment
9. Class D fires are caused by... ANS ignitable metals
10. Flames must be approached from a position. ANS upwind
11. Never approach a flame from a position. ANS downwind
12. Never point a fire extinguisher at the... ANS center of the flame
13. You must point a fire extinguisher at where... ANS the flame begins
14. P.A.S.S stands for... ANS Pull Aim Squeeze Sweep
15. All fire extinguishers must be installed so that they're no more than
feet from the top of the extinguisher and the bottom must not be less than inches from the floor. ANS 5, 4
16. How many feet should a fire extinguisher be within a hot-work area and the fire guards? ANS
30 feet
17. Any single CNG container must not exceed SCF ANS 381
18. LPG Containers must be tested by the DOT approved vendors every
years. ANS 5
20. The use of nonmetallic pipe tubing, or hose for permanently interconnect- ing gas containers is
. ANS prohibited
21. Generally speaking, nonmetallic pipe, tubing and components for any in- stallation, appliance or
equipment using LPG or CNG is prohibited. However, nonmetallic hose may be allowed at. ANS construction sites
22. Hoses must be protected from and no hose is allowed to exceed
feet. ANS physical damage, 30
23. What is Flashback? ANS when a flame burns inside a torch or hose
24. When Flashback happens and there is a hissing/whistling noise, what should you do? ANS
close control valves, close gas container
25. What is Backfire? ANS when the flame on a torch goes out unexpectedly
26. An Acetylene container valve must not be turned more than
turns. ANS 1 ½
27. Soldering and Brazing temperatures are typically F ANS 840
28. For any CNG or LPG torch operation, the first inspection shall be conduct- ed minutes
after completion of torch operations; the second inspection hour after completion of torch operations. ANS 30, 1
29. For any CNG or LPG torch operation, the FIRST inspection shall be conducted
minutes after completion of torch operations ANS 30
30. For any CNG or LPG torch operation, the SECOND inspection shall be conducted hour after
completion of torch operations ANS 1
31. The inspection report must be made available to any representative of the Fire Department and
should be maintained on the premises for... ANS 48 hours
32. Torch Applied Roof-System ANS Bituminous roofing systems using membranes that are adhered by
heating with a torch and melting asphalt back coating instead of mopping hot asphalt for adhesion.
33. It shall be unlawful to install any roofing material using a torch on a roof of... ANS combustible
construction
34. Ducts and conveyor systems that might carry sparks
to distant combustibles must be... ANS shielded, or shut down, or both
35. For hot work operation with citywide permit, the owner of the premises of the hot work
operation areas must be notified in writing by the citywide permit holder at least days before the hot work is to be started. ANS 2
