Docsity
Docsity

Prepare for your exams
Prepare for your exams

Study with the several resources on Docsity


Earn points to download
Earn points to download

Earn points by helping other students or get them with a premium plan


Guidelines and tips
Guidelines and tips

IEC Year 3 Real Exam Questions And Answers 2025 latest update., Exams of Physics

IEC Year 3 Real Exam Questions And Answers 2025 latest update.

Typology: Exams

2024/2025

Available from 05/16/2025

drillmaster
drillmaster 🇺🇸

5

(5)

838 documents

1 / 357

Toggle sidebar

This page cannot be seen from the preview

Don't miss anything!

bg1
IEC Year 3 Real Exam Questions And
Answers 2025.
Which of the following is an example of a load?
I. Relay Coil
II. Solenoid
III. Pilot Light
Select one:
a. I, II & III
b. I only
c. III only
d. I & II only
e. II only
a. I, II & III
A qualified person must be trained in the skills and techniques to determine nominal voltage.
Select one:
a.True
pf3
pf4
pf5
pf8
pf9
pfa
pfd
pfe
pff
pf12
pf13
pf14
pf15
pf16
pf17
pf18
pf19
pf1a
pf1b
pf1c
pf1d
pf1e
pf1f
pf20
pf21
pf22
pf23
pf24
pf25
pf26
pf27
pf28
pf29
pf2a
pf2b
pf2c
pf2d
pf2e
pf2f
pf30
pf31
pf32
pf33
pf34
pf35
pf36
pf37
pf38
pf39
pf3a
pf3b
pf3c
pf3d
pf3e
pf3f
pf40
pf41
pf42
pf43
pf44
pf45
pf46
pf47
pf48
pf49
pf4a
pf4b
pf4c
pf4d
pf4e
pf4f
pf50
pf51
pf52
pf53
pf54
pf55
pf56
pf57
pf58
pf59
pf5a
pf5b
pf5c
pf5d
pf5e
pf5f
pf60
pf61
pf62
pf63
pf64

Partial preview of the text

Download IEC Year 3 Real Exam Questions And Answers 2025 latest update. and more Exams Physics in PDF only on Docsity!

IEC Year 3 Real Exam Questions And

Answers 2025.

Which of the following is an example of a load?

I. Relay Coil

II. Solenoid

III. Pilot Light

Select one:

a. I, II & III

b. I only

c. III only

d. I & II only

e. II only

a. I, II & III

A qualified person must be trained in the skills and techniques to determine nominal voltage.

Select one:

a.True

b.False

a. true

A(n) ___ uses voltages in the range of 50 to 5000 volts to test for insulation damage to conductors or windings.

Select one:

a.megohmmeter

b.ammeter

c.oscilloscope

d.none of these

a. megohmmeter

The training section of an electrical safety program identifies all training required for contractors and vendors.

Select one:

a.True

b.False

a. true

A(n) ___ is a noncontact temperature probe that senses the infrared energy emitted by a material.

An analog meter is ___ than a digital meter.

Select one:

a.less susceptible to electrical noise

b.less accurate

c.both a and b

d.neither a nor b

c. both a and b

Ghost voltages appear on meter displays when the meter is within the electromagnetic field of nearby current-carrying conductors, fluorescent lighting, or operating electrical equipment. This ghost voltage appears when the meter ___ connected to an energized circuit.

Select one:

a.is

b.is not

b. is not

A ___ can be utilized to indicate that a GFCI device has been tripped.

Select one:

a.voltage tester

b.plug-in GFCI receptacle tester

c.either a or b

d.neither a nor b

c. either a or b

A(n) ___ is used to ensure that a motor rotates in the correct direction when connected to a circuit.

Select one:

a.oscilloscope

b.megohmmeter

c.phase sequence indicator

d.digital logic probe

e.ammeter

c. phase sequence indicator

___ is indicated on a clamp-on ammeter when placed within the magnetic field produced around a single conductor.

Select one:

a.Voltage

b.Resistance

c.Current

d.any of these

c. current

When using a meter to test voltage on an energized circuit, no part of your body should touch ___.

Select one:

a.exposed conductors

b.metal tips of test leads

c.both a and b

d.neither a nor b

c. both a and b

OSHA standards require that electrical equipment be ___ before it is serviced or repaired.I. de-energized II. locked III. tagged

Select one:

a.II & III only

b.I & II only

c.I & III only

d.I, II & III

d. I, II & III

One of the most important goals of the Multi-Employer Worksite Policy from OSHA is to ensure that ___.

Select one:

a.Good communication occurs between the contractors working on the site

b.Every contractor on the worksite receives a citation

c.Only the contractor responsible receives a citation

d.The General Contractor will enforce safety on the worksite

a. Good communication occurs between the contractors working on the site

An electrical safety program should include a section on ___.

Select one:

a.Responsibility

b.Procedures

c.Principles

d.All of the above

d. all of the above

A written, documented electrical safety program is ___ than a verbal one.

Select one:

a.More effective

b.Less effective

c.Just as effective

a. more effective

a.True

b.False

b. false

Which of the following devices is not recommended for performing absence of voltage tests?

Select one:

a.Noncontact voltage tester

b.Solenoid voltage tester

c.Digital multimeter

d.High input impedance contact voltage tester

a. noncontact voltage tester

An arc flash hazard analysis is used to determine ___.

Select one:

a.Potential electrical arc flash hazards

b.The Arc Flash Boundary

c.The required PPE

d.All of the above

d. all of the above

The ___ is the distance from exposed energized conductors or circuit parts where bare skin would receive the equivalent of 1.2 cal/cm2.

Select one:

a.Arc Flash Boundary

b.Limited Approach Boundary

c.Prohibited Approach Boundary

d.Restricted Approach Boundary

a. arc flash boundary

The Approach boundaries are viewed as a barrier extending ___ degrees around an exposed energized conductor or circuit part.

Select one:

a.

b.

c.

d.

d. 360

OSHA standards state that electrical equipment must be ___ before preventative maintenance or service is to be performed.

I. locked out II. tagged out

Select one:

e. 50

When performing certain operations on or near energized equipment or circuits, approved ___ clothing must be worn for protection from electrical arcs.

Select one:

a.arc-rated

b.flame-proof

c.both a and b

d.neither a nor b

An arc flash is an ___.

Select one:

a.explosion that occurs when the air surrounding electrical equipment becomes ionized and conductive

b.extremely high temperature discharge produced by an electrical fault in the air

b. extremely high temperature discharge produced by an electrical fault in the air

The entire surface of rubber insulating gloves must be field tested before each use. This testing involves a ___.

Select one:

a.visual inspection

b.manual air test

c.both a and b

d.neither a nor b

c. both a and b

The limited approach boundary (distance from energized parts) ___ vary depending on the voltage.

Select one:

a.does

b.does not

a. does

NFPA 70E states that only qualified persons should test or troubleshoot circuits over ___ volts.

Select one:

a.

b.

c.

d.

d. 50

___ may be damaged or destroyed by electrostatic discharge.

c.III only

d.II & III only

e.I, II & III

a. I & II only

When a short circuit occurs in a circuit where the conduit couplings and connectors are loose, the opening time of an OCPD ___ affected.

Select one:

a.is

b.is not

b. is not

A GFCI enables a circuit to be opened before there is sufficient ground-fault current to cause injury to personnel.

Select one:

a.True

b.False

a. true

The conductor shown at Point C in Figure 306.52 is a(n) ___.

Select one:

a.equipment grounding conductor

b.main bonding jumper

c.grounded conductor

d.grounding electrode conductor

b. main bonding jumper

The definition of an equipment grounding conductor in the NEC® generally covers many different concepts and parts of a grounding system.

Select one:

a.True

b.False

a. true

A circuit is installed in EMT and compression fittings are used. A separate EGC is NOT installed in the conduit. If a ground fault occurs and one or more couplings were never tightened properly, compared to normal operation, the fault current will be ___ and the OCPD will take ___ time to open.

Select one:

a.lower the same

b.higher more

c.higher less

d.lower more

e.lower less

Select one:

a.I & II only

b.II & III only

c.II only

d.I, II & III

e.I only

a. I & II only

A ___ is used to connect the grounding electrode to the equipment or to the grounded conductor at the service equipment.

Select one:

a.grounded conductor

b.grounding electrode conductor

c.main bonding jumper

d.main breaker

b. grounding electrode conductor

The ___ is the connection between the grounded circuit conductor and the equipment grounding conductor at the service.

Select one:

a.grounding electrode conductor

b.main bonding jumper

c.grounded service conductor

d.grounding electrode

b. main bonding jumper

A(n) ___ conductor carries circuit current in normal operation.

Select one:

a.equipment grounding

b.grounding electrode

c.neutral

d.none of these

c. neutral

Which of the following is not an example of a solidly grounded system?

Select one:

a.120/208-volt, three-phase, four-wire

b.120/240-volt, three-phase, four-wire

c.120/240-volt, single-phase, three-wire

d.480-volt, three-phase, three-wire

d. 480-volt, three phase, three wire