


Study with the several resources on Docsity
Earn points by helping other students or get them with a premium plan
Prepare for your exams
Study with the several resources on Docsity
Earn points to download
Earn points by helping other students or get them with a premium plan
Community
Ask the community for help and clear up your study doubts
Discover the best universities in your country according to Docsity users
Free resources
Download our free guides on studying techniques, anxiety management strategies, and thesis advice from Docsity tutors
Neiep 830 Exam With 100% Correct Answers
Typology: Exams
1 / 4
This page cannot be seen from the preview
Don't miss anything!
12 - correct answers ✔✔Although typically horizontal in design, the maximum angle of inclination for the moving walk is ______ degrees 115,15 - correct answers ✔✔A ________ Volt , ______ amp outlet is required by asme for both the upper and lower truss True - correct answers ✔✔True or False Water run off must be seperated before the discharge into the public drains 20 - correct answers ✔✔For drive motors that require overspeed protection, it must stop the systems if speed exceeds ______ % of rated speed Torque - correct answers ✔✔The nameplate on the brake must indicate the ________ setting Drum - correct answers ✔✔The _______ brake is similar to the brake system found on gearless traction elevators Head end - correct answers ✔✔The drive end of a belted walkway is called the _______
3000 - correct answers ✔✔The tensioning device on the tail end of the belted moving walk is normally set at ______ lbs
Crab/circle - correct answers ✔✔The portion of the track system that guides the pallets around the turns are called the ______ tracks False - correct answers ✔✔True or false The lip track is used to restrain the step chain roller from up and down movement 22 - correct answers ✔✔The moving walkway treadway must be at least ______ inches wide True - correct answers ✔✔true or false Belted treadways must be vulcanized to provide a continuous loop Axled and non axled - correct answers ✔✔Palletized chain systems are either ______ or ______ newel wheels - correct answers ✔✔The solid balustrade requires the use of an upper/lower
1/2" - correct answers ✔✔The glass panels are usually (1/8",1/4",1/2") thick V-groove - correct answers ✔✔The _______ handrail is most commonly found on the solid balustrade system Unskirted - correct answers ✔✔Belted treadway moving walks are ( skirted/unskirted ) False - correct answers ✔✔True or false The starting switches are two position on/off , and the key can only be removed in the off
3' or 914.4 mm - correct answers ✔✔Based on the Neiep moving walk final layout what is the normal distance between stanchion in the intermediate section silicone - correct answers ✔✔When installing drip pans , use ________ to seal the joints and where the screws or studs penetrate false - correct answers ✔✔True or false when installing tracks its is best to have all of the joints aligned across from each other and above below each side outer - correct answers ✔✔The ______ decking should be installed before the glass balustrade true - correct answers ✔✔True or false when installing step chain alternate the matched pair lengths 3/16" - correct answers ✔✔There should be no gaps wider than (1/4",1/2",3/16" be between the joints on the interior panels handrail speed monitoring - correct answers ✔✔what monitoring function is bypassed during inspection mode 480V - correct answers ✔✔What voltage should you read on the input to the step down transformer on the the straight line diagram 1/4" - correct answers ✔✔With skirt pandels installed the distance between the edge of the treadway and the skirt panel shall not exceed 1/4",1/2",3/8"