Download Vivint Smart Home Pro Final Exam With 100% Correct Answers … and more Exams Community Corrections in PDF only on Docsity!
Vivint Smart Home Pro Final Exam With 100%
Correct Answers …
12 - 24v - CORRECT ANSWER--What is the input voltage range of the Doorbell Cam? 16.5 VAC - CORRECT ANSWER--What is the output voltage of the transformer used to power the SkyControl panel? true - CORRECT ANSWER--True or False: When programming a sensor into the sky panel you can type in the serial number or "learn" it in by triggering the device 2 - CORRECT ANSWER--When programming a DW21, which loop number is used? 1 2 3 beans and wire caps - CORRECT ANSWER--Which of the following materials can you use to group multiple ground terminals in a takeover module: Solder String Wire Caps Duct Tape Beans True - CORRECT ANSWER--T or F: When installing the firefighter, it is required to test the customer's existing smoke detectors 3/4" - CORRECT ANSWER--When installing a DW21, what size bit should you use to drill the hole for the sensor? 1/2" 3/8" 3/4" 1" True - CORRECT ANSWER--T or F: When installing the TAKE-345, you must ensure that the transformer is supplying power to the power supply before the battery. True - CORRECT ANSWER--T or F: You are required to test signals from all secondary keypads and key fobs even though they are not detection devices False - CORRECT ANSWER--T or F: When running power to the TAKE-345 polarity does not apply
- CORRECT ANSWER--What is the correct height at which to install the PIR2? 7 ft At least 5 ft
At least 7 ft At 7.5 ft How would you program a CO3 if mounted on a hallway wall? Loop 1 Zone 8 Loop 1 Zone 14 Loop 3 Zone 4 Loop 1 Zone 4 - CORRECT ANSWER-- When installing a DW21 into a metal door frame, with a wooden door, what should you be sure to use? Metal Drill bit A DW11 should be used on all metal door frames 3/4" insulated magnet Eye goggles - CORRECT ANSWER-- True - CORRECT ANSWER--T or F: Panic Pendants are programmed as an audible alarm T or F: The Firefighter may be installed next to a stand-alone battery-powered smoke detector - CORRECT ANSWER-- Which of the following zone/sensor types are correct when programming an SMKT3? Type 9 - Freeze Detect Type 7 - Freeze Detect Type 9 - Heat detect Type 6 - heat detect type 1 - heat detect type 8 - freeze detect type 5 - smoke detect type 7 - smoke detect type 9 - smoke detect - CORRECT ANSWER-- When installing a DW21 where is the approved location for the sensor? Anywhere in the door between 6"(15 cm) and 2' (61 cm) from floor Below 6" from the floor Top of the door - CORRECT ANSWER-- T or F: When performing a full system test, you may bypass any open doors or windows - CORRECT ANSWER-- T or F: When installing a translator, you must program all of the existing sensors as new equipment on the panel - CORRECT ANSWER-- When programming a DW11 that has been installing on a window, which zone/sensor type should you use? 10 01 02
When installing a DW11 on a vinyl or metal frame, what should you primarily use to mount the sensor? Provided double sided tape wood glue contractors glue provided wood screws - CORRECT ANSWER--Provided double sided tape Which of the following sensors are you not allowed to program using a translator? Glass break Smoke detector Garage door Motion detector - CORRECT ANSWER-- How often should you perform and inventory reconciliation? Daily Monthly Weekly As needed - CORRECT ANSWER--Weekly What transactions can affect your on hand inventory count? usage pulls trashed equipment damages transfers reconciliations - CORRECT ANSWER-- Before completing reconciliation what should you do? send back bad equipment receive any inventory thats been delivered verify fixparts request are completed complete all tickets for the day receive any pro to pro transfers - CORRECT ANSWER-- Determine HVAC setup based on the following wiring: C, W, Y, Y2, Rc, G Heat Pump, AC powered, 2 stage pump, 1 Aux heat Conventional, Battery powered, 2 stage cool, 2 stage heat Conventional, AC powered, 2 stage cool, 1 stage heat Conventional, Battery powered, 1 stage cool, 2 stage heat - CORRECT ANSWER-- How many stages of cool does a conventional AC unit have if it has both the Y and Y2 wire? 1 2 3 4 - CORRECT ANSWER-- What is the "differential"? Temp. calibration sequence
Number of degrees before the target temp. is reached and the 2nd stage will stop running Number of stages an HVAC has Number of degrees before the heat/AC will kick back on to keep the home at the target temp - CORRECT ANSWER-- Name 2 types of furnaces found on an HVAC system: Gas Solar Conventional Heat Pump Electric - CORRECT ANSWER-- Determine the HVAC setup based on the following wiring: C,B,W2,Y,Rh,G Heat pump, AC powered, 1 stage pump Conventional, AC powered, 1 stage heat, 1 stage cool Heat pump,, AC powered, 1 stage pump, 1 aux heat Conventional, Battery powered, 1 stage cool, 1 stage heat - CORRECT ANSWER-- How many stages of heat does a conventional unit with a furnace have it it has both W and W2 wires? 2 stage 3 stage 4 stage 1 stage - CORRECT ANSWER-- Which of the following untis are not compatible with Vivint systems? Heat Pumps Baseboard heating PID thermostats with A B C wiring Radiators Gas Furnaces - CORRECT ANSWER-- Determine HVAC setup based on the following wiring: B, Y, Y2, Rh, G Heat pump, as powered, 2 stage pump, 1 aux heat Conventional, ac powered, 2 stage cool, 1 stage heat Conventional, battery powered, 2 stage cool, no heat Heat pump, battery powered, 2 stage pump, no aux heat - CORRECT ANSWER-- How can you determine if the HVAC is a heat pump? Turn on the fan, if compressor runs, its A/C. If not, its heat pump Turn on the heat. If comp runs its A/C All external comps are A/C units Turn on the heat, if the compressor runs, its heat pump. - CORRECT ANSWER-- T or F: When installing a deadbolt smartlock, insert the wiring harness below the bolt
- CORRECT ANSWER-- When powering up a deadbolt smart lock for the first time, which of the following must you always do?
