






Study with the several resources on Docsity
Earn points by helping other students or get them with a premium plan
Prepare for your exams
Study with the several resources on Docsity
Earn points to download
Earn points by helping other students or get them with a premium plan
Community
Ask the community for help and clear up your study doubts
Discover the best universities in your country according to Docsity users
Free resources
Download our free guides on studying techniques, anxiety management strategies, and thesis advice from Docsity tutors
A comprehensive set of safety questions and answers for a woodshop environment, covering the safe operation of various tools and machinery. It emphasizes the importance of following safety rules, wearing protective gear, and maintaining a clean and organized workspace. The questions address specific safety procedures for equipment like table saws, radial arm saws, band saws, jointers, drill presses, disk sanders, miter saws, and scroll saws, ensuring students understand how to operate each tool safely. This resource is designed to educate students on potential hazards and best practices to prevent accidents in the woodshop. It also covers general safety guidelines such as proper attire, handling materials safely, and reporting any accidents or violations. The document serves as a valuable tool for instructors to assess students' understanding of woodshop safety and promote a safe working environment.
Typology: Exams
1 / 12
This page cannot be seen from the preview
Don't miss anything!
Safety instructions must be given before you are allowed to work on or operate any machine or ______. ✔✔tool
You are not permitted to work on any equipment or machine if the ________ is not present. ✔✔teacher
Guards and safety devices must be on all machines during ______. ✔✔operation
Machinery must not be oiled or adjusted while in ______. ✔✔use
A machine must be started and stopped only by the ______. ✔✔operator
Do not leave a machine while it is ______. ✔✔running
When working on or near any machine or tool where there is a possibility of eye injury, you must wear _________. ✔✔eye protection
You are not permitted within the safety zone around any machine unless you are the ________. ✔✔operator
Loose clothing must be tucked in before you start work, as a precaution against __________. ✔✔getting caught/entangled
If in doubt about any machine, check with the ________. ✔✔Teacher
Aisles and working areas must be kept clear of ___________. ✔✔all obstructions
The shop floor must be kept free of oil because of the danger of fire and ________. ✔✔slipping
Combustible rags must be kept in a closed __________. ✔✔red container
Do not lift materials heavier than your ability to handle them ________. ✔✔safely
Long pieces of material should be carried by ________. ✔✔2 people
When using a screwdriver, avoid holding the material in the _______. ✔✔hand
After clamps have been applied to the work, it should not be ________. ✔✔moved
Face shields or goggles/glasses must be worn by shop students when there is a possibility of __________. ✔✔loose debris
Whenever possible, the ________ should be clamped. ✔✔project stock
All adjustments should be made before the machine is ________. ✔✔turned on
The operator must keep his/her fingers away from the _______ spindle, chuck, and bit. ✔✔spinning
When operating the drill press, ______ the material instead of holding it by hand. ✔✔clamp
Before turning on the power, the chuck key should be __________. ✔✔removed from the chuck
When the drill begins to break through the work you should ease up on the ________. ✔✔forward pressure
Chips should be removed from the drill press table when the machine is _________. ✔✔turned off
When the drill is being tightened in the chuck, the cord should be _______. ✔✔unplugged
The operator should be ready to stop the _______ instantly. ✔✔machine
To prevent the work from being caught, the tool rest must be kept within ________ of the grinding wheel. ✔✔1/8"
Grinding on the ______ of the wheel may produce pressure which can cause the wheel to break. ✔✔edge
When using the buffer, the operator must use ______ to control the work being buffed. ✔✔both hands
Do not adjust the tool rest when the stock is ______. ✔✔turning
The amount of clearance between the tool rest and the stock should not exceed ______. ✔✔1/4"
Before the machine is turned on, all adjustments involving the table, stops, and _____ should be completed. ✔✔depth
What one must wear at all times working with any type of tool or machine ✔✔safety goggles
What is one thing not acceptable at any time while in the tech room ✔✔messing around
If one has long hair one should always ✔✔pull it up or tuck it in
If one doesn't feel comfortable operating one should ✔✔ask for help
_________ twice and ___________ once ✔✔measure;cut
__________ is cutting with the grain and ________ is cutting against the grain ✔✔ripping;cross cutting
Wait for the machine to come up to ___ before using ✔✔speed
Do not cut/drill too ___ ✔✔fast
Never leave tools or debris on the ___ ✔✔table
When cutting a long piece of wood always ask for ___ ✔✔help
When ripping a piece of wood on the table saw one should always use the ___ ✔✔fence
Never cut ___ on the table saw ✔✔free hand
one edge of the wood should be ___ before cutting ✔✔jointed
how high should the blade be above the wood on the table saw ✔✔1/4 to 1/
If the blade should break on the bandsaw turn the power ___ ✔✔off
Turn the machine __ if the blade is stuck and you can't work the piece to get the blade out ✔✔off
The smallest width you can through the jointer is __ of an inch ✔✔1 and 3/
Material must be held down firmly against the ____ and against the ___ when jointing a piece of wood ✔✔table;fence
Don't interrupt a cut or try to back out of a cut bc the material can cause ___ ✔✔kickback
Always place a piece of scrap wood on the __ of the drill ✔✔table
Check and adjust the depth of the cut being drilled with the motor __ before drilling ✔✔off
Always hold the material being drilled firmly against the table of the __ to prevent the material from spinning ✔✔pole
The general purpose of the disk sander is to sand the __ of the wood not the __ of the wood ✔✔edge;face
Always put the material being sanded on the __ Side of the table where the disc is heading downward towards the table ✔✔left
After turning off the sander always stay there until it comes to a complete ___ ✔✔stop
Always check the board for __ before cutting it ✔✔metal
Never plane a board that is less than __ inches long ✔✔ 12
Never make cuts deeper than ___ of an inch at a time ✔✔1/
Never adjust the __ of the cut while it is an operation ✔✔depth
The Miter saw is primarily used for cutting ___ and ___ ✔✔angles and crosscutting